PYLE Audio Projector PRJV66 User Manual

Multimedia Lcd Projector  
Model : PRJV66  
User Manual  
 
Read this manual carefully before using this product. Heed the  
instructions to keep your warranty for this product. Prevent fire or  
electric shock. This product may only be repaired by qualified  
servicing personnel. Keep this manual for future reference.  
-
Keep the original packaging in case of defects. Return the product in its original  
packaging.  
-
Consult a professional before installing this product.  
- This product contains high-voltage parts; NEVER open the housing!  
-
Never pull the power cord while disconnecting it from the mains socket. Remove the  
power cord by pulling the connector.  
-
-
Never connect or disconnect the power cord with wet hands.  
If the connector or the power cord is damaged; they need to be replaced (or repaired) by  
a qualified serviceman.  
-
If the housing is damaged in such away so you can see internal parts, you may NEVER  
connect the power cord with the mains socket and you may NEVER switch the product  
on. Please contact your dealer if this situation occurs.  
- This product may only be repaired by qualified servicing personnel.  
-
-
Only connect this product with a 230VAC/50Hz earthed power supply.  
Don't install this product near heat sources like radiators etc. Don't install on vibrating  
surfaces.  
- Always disconnect this product during thunderstorms. Also disconnect this product when  
not in use for a long period of time.  
- Water vapour might occur at first use after a long period of not using this product. Please  
let the product reach room temperature before using it.  
-
Never use this product outdoors or in a wet environment.  
- To prevent accidents in professional environments; please heed instructions and  
guidelines at all times.  
-
-
Keep this product out of reach of children.  
Don't use cleaning spray to clean this product. Remainders of cleaning sprays are  
responsible for the build-up of dust and grease. Please contact a servicing company  
when this product is malfunctioning.  
-
-
-
-
-
Please clean your hands before using this product.  
Don't use excessive force while controlling this product.  
Place this product on a stable and a evened surface.  
NEVER look directly in the projection lens.  
Only power this product off when the fan stops blowing; the lamp may blow during  
abrupt shutdowns? this may cause fire or electric shock.  
NEVER touch the grille or bottom part of the housing because of heated airflows.  
Clean the air filter at least once a month and NEVER look directly into the air filter  
during operation.  
-
-
-
-
Never clean this product with chemical solutions. This might damage the paint. Use a  
dry cloth instead.  
Install out of the way of electronic devices that might cause humming malfunctions with  
this product.  
- Only use identical servicing parts when servicing this product. Irreparable damages or  
radiation might occur.  
2
 
- Turn this product of before disconnecting it from the mains power supply. Remove the  
power chord and other connection cables before (re)moving this product.  
MAINTENANCE FILTER  
-
Don't damage the power chord by stepping on it. NEVER install this product across  
walking routes.  
The filter should be cleaned at least once a month (more often in dusty environments), or  
the projector will overheat.  
- This product requires a 230VAC/50Hz power supply. Please inform if you're mains  
supply meets these specifications. When you use this product abroad, please inform if  
the mains supply meets the above requirements.  
1. Turn the projector of with the On/Off switch  
and remove the plug from the mains supply.  
Never turn the projector on without a filter.  
2. Remove the grille like indicated below  
(arrows).  
This marking means that this product operates on a highly dangerous voltage.  
By touching the internal, electrical parts you risk suffering an electric shock  
which might result in harmful damage to you or others in the direct area.  
3. Use the smallest amount of water or thinned  
dish cleanser to clean the filter. Dry the filter  
sufficiently. Never install a moist filter in this  
projector.  
This marking means that it's very important to read and heed the instruction  
manual at all times.  
4. Follow the steps (1-2) in opposite order to  
complete the installation.  
PRODUCT DESCRIPTION  
ACCESSOIRIES  
This projector was designed using highly advanced technology and can be used in schools,  
companies, institutes, meeting rooms, hotels, clubs, supermarkets, theatres etc.  
Thank you for buying this Multimedia LCD Projector! Please check if the following  
accessories are included in the package:  
Because of the compact dimensions of this product you can carry it to any place you like.  
Projector  
1
1
1
1
1
1
You can connect this product with computer and video input signals. (Computer resolutions  
up to 1024 768 and video signals like DVD, VCR, TV, SVHS etc.). Resolutions over  
1024 768 are not connectable. Please reduce your computer's resolution before connecting  
it with this product.  
Remote control  
Power cord  
Fuse (5A)  
Lens cloth  
Manual  
If a trapezoid image occurs you can adjust this with the Keystone-correction and solve the  
problem.  
The OSD menu can be called upon with the remote control (IR function).  
The OSD language can be set to English as well as Chinese-simp, Spanish, French, German,  
Italian, Russian, Portuguese.  
14  
3
 
TROUBLE SHOOTING  
SPECIFICATONS  
Please refer to this chapter when you encounter a problem list prior to contacting your  
dealer.  
Power consumption: ....................................................... <220 W  
Lamp power: .................................................................... 150 W  
Color temperature: ......................................................... 9300 K  
Lamp life: ....................................................................8000 Hrs  
Power requirements: .......................................... 230 VAC/50 Hz  
Running current: ................................................................. <2 A  
Brightness: ................................................................. 1200 Lm  
Resolution.......................................................800*600  
Lens: ....................................................................f160mm/F=2.9  
Contrast: ............................................................................800:1  
Number of Pixels: .............................................................. 1.0 M  
Color system: ............................................. NTSC/PAL/SECAM  
Keystone-correction: ........................................................... 15  
Problem:  
Possible solution(s):  
Projector not connected to mains.  
Projector not turned on.  
Blown fuse.  
No power  
Remote doesn't operate  
Projector turned on to quickly after last  
turn off (needs 5 minutes).  
Batteries defect.  
Aim remote correctly at IR receiver.  
No image  
Lens cap not removed.  
Projector turned off.  
Faulty wiring.  
Selected the wrong input signal.  
Projector turns off automatically  
(no more power)  
Air in-and/or outlets and/or filter  
are covered or blocked.  
Lamp doesn't function  
Power supply isn't correct.  
Temperature is too high.  
Defect lamp.  
Max. advisable duration of usage: ..............................  
24 Hrs  
REPLACING THE LAMP  
Projection picture size: ............................................ 50-100 inch  
Dimensions: ..................................................310 255 95 mm  
Weight: ............................................................................. 6 Kg  
This lamp has a maximum lamp life. The color balance will change when the light intensity  
decreases. The image will also blur. Replace the lamp if this is the case.  
Turn the projector of and remove the power cord.  
1. Place the projector on a cloth to put loose parts on.  
2. Turn the screw loose and open the lid.  
Specifications and design may be altered by the manufacturer  
without any communication.  
3. Remove the 4 screws holding the lamp unit. Pull the unit straight up.  
4. Now replace the lamp and follow the steps (1-4) in opposite order to complete the  
installation.  
4
13  
 
OSD menu  
Menu setting method  
PROJECTOR INSTALLATION  
1. Using the projector press menu key,  
enter the main menu window (picture one)  
Please use the setup indicated below:  
Bright  
Contrast  
Color  
2. Press  
key the menu enter  
Tone  
Sharpness  
English  
into image  
>
volume  
system  
image secondary menu  
>
Speaker  
L
Speaker  
R
function  
>
>
setting  
>
Screen  
Subwoofer  
3.Enter the secondary menu use  
to elect the function (picture two  
key  
Speaker C  
4. use  
key to change the parameter  
5. Finished to adjust the parameter press the  
menu key again exit the window  
6. Repeat operate the 2 5step  
till finished all the parameter's setting.  
press exit key,exit the menu window  
Sharpness  
English  
Volume menu adjustment  
Adjust the volume of the speaker or amplifier equipment  
b. Choose the audio output method when setting as line  
the projector speaker will stop work.  
DVD  
Projector  
Amplifier  
Volume  
Output  
Volume  
Output  
50  
speaker  
speaker  
Appreciate seats  
Door  
Function menu adjustment  
a. Switch image display mode (From 16:9 to 4:3 ,zoom function)  
b. Setting the menu auto-exit time  
Speaker  
Ls  
Speaker  
Rs  
c. Setting Blue screen or no when no signal input.  
Zoom  
OSD.Time  
Bluescreen  
4 3  
5
OFF  
Zoom  
OSD.Time  
Bluescreen  
4 3  
5
OFF  
SETTING UP THE SCREEN AND PROJECTOR  
Place the projector on a smooth and stable surface. Please don't place any objects on top,  
underneath or next to this product to ensure proper and sufficient cooling. De distance  
between the projector and the projector screen varies from the screen's size. Please refer to  
the table below for the correct setup distances.  
TV mode  
AV/SV mode  
Screen Size  
50"  
4:3  
16:9  
4. System menu adjustment  
a. Colour -S can choose auto PAL NTSC SECAM four mode  
when the projector connect the new video devices if you don't know  
which system of the video output signal please setting Colour -S  
as auto  
2.45m  
3.45m  
4.73m  
2.65m  
3.75m  
5.15m  
72"  
100"  
12  
5
 
Please follow the instructions below when a trapezoid occurs on the projector screen:  
FOCUSING AND KEYSTONE ADJUSTMENT  
Screen  
FOCUSING  
Turn the lens to focus the projected image.  
Screen  
symmetry  
axis  
Projector  
NOTE: When you replace the projector from a cold to a warm environment water vapour  
might occur. Don't turn the projector on when this occurs but wait until the vapour  
has disappeared.  
Installed correctly,  
the image is rectangular.  
Incorrect installation,  
the images left-right small.  
Incorrect installation,  
the images right-left small.  
CEILING/TABLE MOUNT SETUP  
KEYSTONE  
Contact a professional service man to mount this projector to a ceiling. Follow the  
instructions below for the correct projector positions:  
If a projected picture has keystone distortion, correct image with Keystone adjustment. The  
image becomes trapezoid shape when the screen or project is not level. Please reposition  
the projector to improve its angle to the screen. However, the circumference of the image  
may not be focussed.  
Projector  
Projector  
Screen  
Screen  
Projector  
Front projection ceiling mount  
Rear projection ceiling mount  
Projector  
Screen  
Screen  
Keystone  
Screen  
Screen  
Projector  
Projector  
Front projection table mount  
Rear projection table mount  
If not able to use the Keystone correction function to correct the trapezoid distortion, please  
reduce of the projector to centre the screen vertically.  
WARNING  
This projector might damage beyond repair when it's incorrectly mounted on a ceiling or  
when its incorrectly installed on a surface or installed on a incorrect surface. It may also  
inflict damage to persons within close vicinity.  
This projector can only be used in an environment with a temperature not exceeding the  
range of 0~35 . The projector may malfunction if temperatures vary outside the normal  
operating range.  
The sharpness of the screen might be interrupted when the projector is being used in a  
dusty, wet, moist or smoke filled environment. The projector might malfunction in a moist  
or wet environment. Take care of sufficient ventilation around the projector. Otherwise this  
projector might overheat and cause life threatening situations!  
6
11  
 
PROJECTOR (FRONT VIEW)  
MAKING CONNECTIONS  
The sockets for making connections on the back panel of the projector are shown below:  
TOP-Key  
Fan grille  
Keystone  
Lens  
button: Push this button to turn the projector on when it's in stand-by mode and  
push it again to return to stand-by mode.  
Video input: Connect with a composite output signal from a video device.  
Audio input: Connect with an audio signal from a video or audio device.  
VGA input: Connect with a computer output signal.  
MENU button: Push this button to open the menu.  
/
/
/
buttons: Use these buttons to navigate through the menu.  
PC/AV button: Use this button to select the video source you want to use. You can  
select between signals like PC, VCR or DVD. The beamer will switch between  
video sources every time you push this.  
S-Video input: Connect with an S-video output signal from a video device.  
RF input: Connect the antenna of the wired television.  
LED indicator: Put the projector into stand-by mode ,the LED is flashing; when the  
projector is working, the LED is light red.  
Fan grille: Cool air inlet.  
AC Power Switch:Turn the projector on  
or off. When using Remote Control  
Unit, turn the switch to ON. And turn it  
to OFF when the projector is not used.  
Focusing the image by turning the lens.  
PROJECTOR CONTROL  
Here is a 5 Amps fuse installed for the  
projector.  
Remove the lens cap after connecting the mains cable.  
1. Insert 2 batteries in the battery compartment.  
AC Power Jack: Connect AC Power  
Cable (supplied) to the projector.  
2. Turn the On/Off switch to "ON"; the LED will  
flash slowly.  
3. Push the "ON" button on your remote or the  
one on the projector. The LED will light up red.  
4. Hold one of these buttons for 2 seconds. The lamp will warm-up now. After 2 minutes  
the image appears on the projector screen.  
IR receiver  
5. Focus the image with the lens and setup the size and position of the image. You can  
correct the Keystone if necessary.  
6. Setup the required image quality with the OSD menu.  
7. Push the "ON" button again and the lamp will switch off.  
8. The LED will flash rapidly and the fans will keep operating for around 5 minutes to cool  
the projector. Do not turn the projector on again during this period!  
10  
7
 
CONNECT MAIN EQUIPMENT  
REMOTE CONTROL  
POWER button: Push this button to turn the projector on when it's in stand-by  
mode and push it again to return to stand-by mode.  
MENU button: Push this button to open the menu.  
/
/
/
buttons: Use these buttons to navigate through the menu.  
AV/PV button: Use this button to select the video source you want to use. You can  
select between signals like PC, VCR or DVD. The projector will switch between  
video sources every time you push this.  
Connecting video equipment  
Without S-video output terminal.  
Connecting audio equipment  
With RCA output terminal.  
POWER  
For turning the power on.  
MUTE  
For temporarily turning off  
the sound.  
RETURN  
Cancel the direct channel  
selection.  
Number Amount  
Selects the amount of TV  
channel number display.  
DISPLAY  
Information display.  
Number Buttons  
Selects TV channel directly.  
PICTURE MODE button  
For selecting image effect: bright, soft,  
normal, user.  
AV/TV  
For selecting input source.  
Adjustment buttons  
Selects a channel.  
Selects (vertically) or adjusts  
an operation or item.  
Volume control.  
Selects (horizontally) or  
adjusts an operation or item.  
Connecting an cable with  
matched receiving antenna.  
Connecting PC or DVD  
equipment VGA output terminal.  
MENU  
For displaying adjustment  
and setting screens.  
DISPLAY MODE  
16:9 or 4:3.  
PICTURE OVERTURN  
For selecting the image display  
modes.  
No using.  
Connecting video equipment  
With S-video output terminal.  
PRECAUTIONS  
You need to dry the remote control with a dry cloth immediately when it gets wet.  
When the battery hasn't been used for a long time we advise you to remove it from  
the remote. Be sure that children can't reach the removed button cell. Swallowing a  
button cell will cause a child a lot  
of harm and is very dangerous!  
8
9
 

Philips Air Cleaner AC4105 00 User Manual
Philips Car Video System CID3292 User Manual
Philips Headphones SHN6000 User Manual
Philips Telephone Accessories SDJ6360W User Manual
Philips TV Converter Box SWS2104W User Manual
Pioneer Car Video System AVH P4000DVD User Manual
Pioneer DVD Player 655A User Manual
Planar Computer Monitor PE1500 User Manual
Plantronics MP3 Player Accessories M12 User Manual
Professional Series Burner PS77301 User Manual