Pelco Home Security System c684M A User Manual

®
DX9000 Series  
Video Storage Unit  
Installation/  
Operation Manual  
C684M-A (7/01)  
U
®
L
LISTED  
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150 • DataFAX (800) 289-9108  
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120 • DataFAX +1(559) 292-0435  
PelcoEurope BV • Dillenburg Center, Dillenburgstraat 7C • 5652 AM Eindhoven • The Netherlands  
Tel +31(40) 251-9870 • FAX +31(40) 251-9835  
 
CONNECTIONS  
One, two, three, or four video storage units can be connected to a recorder, depending on  
the requirements of your system.  
Refer to Figure 2 to install the storage units.  
1. Connect the appropriate end of the SCSI cable to the SCSI connector on each video  
storage unit.  
2. Read the Caution Notice in the Mounting section. Connect the other end of the  
SCSI cable from each video storage unit to the SCSI connector in slot 1 of the re-  
corder. Connect the first storage unit (labeled 01) to the upper left connector. Connect  
the second storage unit (labeled 02) to the upper right connector. Connect the third  
storage unit (labeled 03) to the lower left connector. Connect the fourth storage unit  
(labeled 04) to the lower right connector.  
3. Select the appropriate power cord (USA or European standard) and plug it into the  
power receptacle on the back of each video storage unit. Plug the other end into a  
power supply, preferably through an uninterruptible power supply.  
4. Turn on the power switch on the back of one of the video storage units. Then open the  
front door with the supplied key. Press the square button to turn on the power. Close  
the door. The LEDs on the front of the unit light to show the hard drives are working.  
NOTE: All video storage units  
connected to a recorder must  
be turned on before turning  
on the recorder.  
5. Repeat step 4 for each storage unit.  
6. Turn on the power switch on the back of the recorder. Then open the front door with  
the supplied key. Press the square button to turn on the power. Close the door.  
7. Go to the System Configuration section of the Installation/Operation Manual for the  
Digital Video Recorder to continue with the installation procedure.  
RECORDER  
STORAGE UNIT #1  
*
STORAGE UNIT #2  
*
STORAGE UNIT #3  
*
STORAGE UNIT #4  
*
** STORAGE UNITS ARE NUMBERED AND MUST BE CONNECTED TO THE PROPER CONNECTOR.  
00850  
Figure 2. Connection Storage Units to Recorder  
Pelco Manual C684M-A (7/01)  
3
 
SPECIFICATIONS  
ELECTRICAL/VIDEO  
Input Voltage:  
Power Consumption:  
Recording Resolution  
NTSC:  
100-240 VAC, 50/60 Hz, auto-ranging  
250W maximum  
352 x 240 pixels  
384 x 288 pixels  
MPEG1  
PAL:  
Compression:  
Compressed Image Size: 352 x 240; average 1.4 kB  
Remote Control:  
Full remote control via TCP/IP network  
MECHANICAL  
SCSI Connector:  
Recorder interface  
GENERAL  
Operating Temperature:  
Relative Humidity:  
Dimensions  
41° to 104°F (5° to 40°C)  
Maximum 80% non-condensing  
Desktop:  
Rack Mount:  
Unit weight:  
7.3 (H) x 17.0 (W) x 19.6 (D) inches (18.5 x 43.2 x 49.8 cm)  
7.0 (H) x 19.0 (W) x 19.6 (D) inches (17.8 x 48.3 x 49.8 cm)  
45 lb (20.4 kg) maximum (fully equipped)  
(Design and product specifications subject to change without notice.)  
REGULATORY NOTICES  
This equipment has been tested and found to comply with the limits of a Class A digital de-  
vice, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable  
protection against harmful interference when the equipment is operated in a commercial envi-  
ronment. This equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instruction manual, may cause harmful interference  
to radio communications. Operation of this equipment in a residential area is likely to cause  
harmful interference in which case the user will be required to correct the interference at his  
own expense.  
WARRANTY AND RETURN INFORMATION  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100  
or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide  
the following information:  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective  
in material or workmanship for a period of one year after the date of shipment.  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on Pelco manufactured cameras (CC3500/CC3600 and MC3500/  
MC3600 Series); two years on all other cameras.  
Three years on GenexSeries (multiplexers, server, and keyboard).  
Two years on all standard motorized and fixed focal length lenses.  
Two years on Legacy®, CamclosureCamera Systems, CM6700/CM6800/  
CM8500/CM9500/CM9740/CM9750/CM9760 Matrix, DF5 Series and DF8  
Fixed Dome products.  
If there is a dispute regarding the warranty of a product which does not fall under  
the warranty conditions stated above, please include a written explanation with  
the product when returned.  
Method of return shipment shall be the same or equal to the method by which  
the item was received by Pelco.  
Two years on Spectra® and Esprit, including when used in continuous mo-  
tion applications.  
Two years on WW5700 series window wiper (excluding wiper blades).  
Eighteen months on DX Series digital video recorders.  
Six months on all pan and tilts, scanners or preset lenses used in continu-  
ous motion applications (that is, preset scan, tour and auto scan modes).  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call  
the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number  
(CA number if returned for credit, and RA number if returned for repair). Goods  
returned for repair or credit should be clearly identified with the assigned CA/RA  
number and freight should be prepaid. All merchandise returned for credit may  
be subject to a 20% restocking and refurbishing charge.  
Pelco assumes no risk and shall be subject to no liability for damages or loss  
resulting from the specific use or application made of the Products. Pelco’s li-  
ability for any claim, whether based on breach of contract, negligence, infringe-  
ment of any rights of any party or product liability, relating to the Products shall  
not exceed the price paid by the Dealer to Pelco for such Products. In no event  
will Pelco be liable for any special, incidental or consequential damages (includ-  
ing loss of use, loss of profit and claims of third parties) however caused, whether  
by the negligence of Pelco or otherwise.  
Ship freight prepaid to: Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
The above warranty provides the Dealer with specific legal rights. The Dealer  
may also have additional rights, which are subject to variation from state to state.  
REVISION HISTORY  
Manual # Date  
Comments  
C684M  
4/01  
7/01  
Original version.  
C684M-A  
Revised Description, Installation, and Connections sections. Added FCC notice.  
® Pelco, the Pelco logo, Spectra, Genex, and Legacy are registered trademarks of Pelco.  
™ Esprit and Camclosure are trademarks of Pelco.  
© Copyright 2001, Pelco  
All rights reserved.  
4
Pelco Manual C684M-A (7/01)  
 

Philips Digital Camera SPC890NC User Manual
Philips DVR VR140 User Manual
Philips Portable Speaker SBA1710 User Manual
Philips Stereo Amplifier SDW1410 User Manual
Philips TV Converter Box SWS2101W User Manual
Planet Technology Stereo System WL 3565 User Manual
Planet Technology Telephone VIP 150T User Manual
Porter Cable Air Compressor C2150 User Manual
Powermate Portable Generator PM054500701 User Manual
ProForm Treadmill 830QT User Manual