Philips Car Speaker SB365 User Manual

Always there to help you  
Register your product and get support at  
SB365  
Question?  
Contact  
Philips  
User manual  
 
Contents  
1 Important  
2
Safety  
2
2 Your Bluetooth speaker  
Introduction  
3
3
3
4
What's in the box  
Overview of the speaker  
3 Get started  
Power supply  
Turn on  
5
5
5
4 Play from Bluetooth-enabled devices 6  
Connect a device  
Play from Bluetooth device  
Clear the pairing information  
6
7
7
5 Other features  
Charge your mobile devices  
Listen to an external device  
Adjust volume  
7
7
7
8
6 Product information  
8
8
Specifications  
7 Troubleshooting  
General  
9
9
About Bluetooth device  
10  
8 Notice  
10  
Disposal of your old product and  
batteries  
11  
EN  
1
 
l Refer all servicing to qualified service  
personnel. Servicing is required when  
the apparatus has been damaged in any  
way, such as liquid has been spilled or  
objects have fallen into the apparatus, the  
apparatus has been exposed to rain or  
moisture, does not operate normally, or  
has been dropped.  
1 Important  
Safety  
m Battery usage CAUTION To prevent  
battery leakage which may result in bodily  
injury, property damage, or damage to  
the unit:  
Warning  
Never remove the casing of this speaker.  
Never lubricate any part of this speaker.  
Never place this speaker on other electrical equipment.  
Keep this speaker away from direct sunlight, naked  
flames or heat.  
Install all batteries correctly, + and - as  
marked on the unit.  
Do not mix batteries (old and new or  
carbon and alkaline, etc.).  
Remove batteries when the unit is not  
used for a long time.  
Important safety instructions  
n Battery shall not be exposed to excessive  
a Read these instructions.  
b Keep these instructions.  
c Heed all warnings.  
heat such as sunshine, fire or the like.  
o Apparatus shall not be exposed to  
dripping or splashing.  
p Do not place any sources of danger on  
the apparatus (e.g. liquid filled objects,  
lighted candles).  
d Follow all instructions.  
e Do not use this apparatus near water.  
f Clean only with dry cloth.  
q Where the plug of the Direct Plug-in  
Adapter is used as the disconnect device,  
the disconnect device shall remain readily  
operable.  
g Do not block any ventilation openings.  
Install in accordance with the  
manufacturer's instructions.  
h Do not install near any heat sources such  
as radiators, heat registers, stoves, or  
other apparatus (including amplifiers) that  
produce heat.  
Note  
The type plate is located on the bottom of the  
apparatus.  
i Protect the power cord from being  
walked on or pinched, particularly at  
plugs, convenience receptacles, and the  
point where they exit from the apparatus.  
j Only use attachments/accessories  
specified by the manufacturer.  
k Unplug this apparatus during lightning  
storms or when unused for long periods  
of time.  
2
EN  
 
2 Your Bluetooth  
speaker  
Congratulations on your purchase, and  
welcome to Philips!To fully benefit from the  
support that Philips offers, register your product  
Introduction  
With this product, you can  
play audio from Bluetooth-enabled devices,  
or other external devices;  
charge your mobile devices.  
What's in the box  
Check and identify the contents of your  
package:  
Main unit  
Power adaptor  
Audio-in cable  
Short user manual  
EN  
3
 
Overview of the speaker  
b
c
d
a
d
e
f
g
a NFC  
d -VOL/VOL +  
Connect a device with NFC feature  
Adjust volume.  
through Bluetooth.  
e CHARGING  
b
c
Charge mobile devices.  
Bluetooth indicator.  
f AUDIO IN  
Connect an external audio device.  
Turn on the speaker or switch to  
standby mode.  
g DC IN  
Connect power.  
Disconnect the paired device.  
Enter Bluetooth pairing mode.  
Clear Bluetooth pairing information.  
4
EN  
 
Option 2:AC power  
3 Get started  
Caution  
Always follow the instructions in this chapter in  
sequence.  
Risk of product damage! Make sure that the power  
voltage corresponds to the voltage printed on the back  
or underside of the speaker.  
Risk of electric shock! When you unplug the AC  
adapter, always pull the plug from the socket. Never  
pull the cord.  
Power supply  
Connect the power adaptor to:  
Either AC power or battery can be used as  
power supply of this product.  
the DC IN socket at the back of the  
speaker.  
the wall outlet.  
Option 1: Battery power  
Caution  
Risk of explosion! Keep batteries away from heat,  
sunshine, or fire. Never discard batteries in fire.  
Batteries contain chemical substances, so they should  
be disposed of properly.  
Note  
Turn on  
Batteries are not supplied with the accessories.  
If battery is low, the button flashes when the speaker  
is turned on.  
Press .  
» The speaker switches to Bluetooth  
mode.  
To install the batteries:  
» The Bluetooth indicator begins to flash.  
1 Open the battery compartment.  
2 Insert 4 AA batteries with correct polarity  
Switch to standby mode  
(+/-) as indicated.  
3 Close the battery compartment.  
The speaker switches to standby mode in the  
following situation:  
Press again;  
The connection with Bluetooth device or  
other device is invalid for 15 minutes; or  
Music playback is stopped for 15 minutes.  
EN  
5
 
» After successful pairing and connection,  
the speaker beeps twice, and the  
4 Play from  
Bluetooth-  
Bluetooth indicator turns solid blue.  
To disconnect the Bluetooth-enabled device:  
Press and hold for 3 seconds;  
Disable Bluetooth on your device; or  
Move the device beyond the  
communication range.  
enabled devices  
With this product, you can listen to audio from  
Bluetooth-enabled devices.  
To reconnect the Bluetooth-enabled device:  
Next time you turn on the speaker, the  
speaker will reconnect the last connected  
device automatically; or  
On your Bluetooth device, select “PHILIPS  
SB365“ on your Bluetooth menu to start  
connection.  
Connect a device  
Note  
To connect another Bluetooth-enabled device:  
Make sure that your Bluetooth device is compatible  
with this speaker.  
Before pairing a device with this speaker, read its user  
manual for Bluetooth compatibility.  
The speaker can memorize a maximum of 4 paired  
devices.  
1 Press and hold for 3 seconds to  
disconnect the currently connected device;  
» The speaker enters Bluetooth pairing  
mode.  
Make sure that Bluetooth function is enabled on your  
device, and your device is set as visible to all other  
Bluetooth devices.  
2 Connect another Bluetooth device.  
Any obstacle between this speaker and a Bluetooth  
device can reduce the operational range.  
Keep away from any other electronic device that may  
cause interference.  
Connect a device through NFC  
Near Field Communication (NFC) is a  
technology that enables short-range wireless  
communication between various NFC  
compatible devices, such as mobile phones and  
IC tags.  
Connect a device manually  
If your Bluetooth device supports NFC, you can  
connect it with this speaker easily.  
Note  
1 Press on the speaker.  
» The Bluetooth indicator begins to  
flash.  
The operational range between this speaker and a  
Bluetooth device is approximately 10 meters (30 feet).  
1 Press on the speaker.  
» The Bluetooth indicator begins to  
flash.  
2 Enable the NFC feature on your Bluetooth  
device (see the user manual of the device  
for details).  
3 Touch the NFC tag on the speaker with  
2 On your Bluetooth device, enable  
Bluetooth and search for Bluetooth devices  
(refer to the user manual of the device).  
the back of your Bluetooth device.  
3 When [Philips SB365] is displayed on  
your device, select it to start pairing and  
connection. If necessary, enter default  
password “0000”.  
6
EN  
 
5 Other features  
Charge your mobile devices  
With this speaker, you can charge your mobile  
devices through the CHARGING socket.  
4 On your Bluetooth device, accept the  
pairing request with "SB365". If necessary,  
input "0000" as the pairing password.  
Note  
The USB socket is used for charging only.  
5 Follow the on-screen instructions to  
complete the pairing and connection.  
» After successful pairing and connection,  
the speaker beeps twice, and the  
In AC power supply mode, connect to  
your mobile device with a USB cable (not  
supplied).  
Bluetooth indicator turns solid blue.  
» Once the device is recognized, the  
charging starts.  
LED indicator  
Description  
Flashing blue  
Connecting or waiting for  
connection  
Solid blue  
Connected  
Play from Bluetooth device  
CHARGING  
After successful Bluetooth connection, play  
audio on the Bluetooth device.  
» Audio streams from your Bluetooth  
device to the speaker.  
Clear the pairing information  
In Bluetooth mode, press and hold for 8  
seconds.  
Listen to an external device  
» All the Bluetooth pairing information  
is erased.  
With this speaker, you can also listen to an  
external audio device such as an MP3 player.  
EN  
7
 
Note  
6 Product  
information  
Make sure that there is no Bluetooth connection, or  
music playback through Bluetooth is paused.  
Note  
1 Connect the supplied audio input cable to  
the AUDIO IN socket on this speaker,  
Product information is subject to change without prior  
notice.  
and  
the headphone socket on the external  
device.  
Specifications  
Amplifier  
Rated Output Power  
Signal to Noise Ratio  
AUX Input  
2 X 4 W RMS  
> 65 dBA  
600 mV  
Bluetooth  
Bluetooth version  
Supported profiles  
Range  
V4.0  
A2DP,AVRCP  
10 m (Free space)  
General information  
Power Supply  
- AC Power  
2 Play audio on the external device (refer to  
its user manual).  
Brand name: PHILIPS;  
Power adapter A:  
(power adapter)  
Adjust volume  
Model: OH-  
1015A0901660U1-UL;  
Input: 100-240V~,  
50/60 Hz, 350 mA;  
Output: 9V 1.66 A;  
Power adapter B:  
Model: TPA103B-  
15090-US;  
During play, press VOL + or -VOL to increase  
or decrease volume.  
Note  
When the volume reaches the minimum or maximum,  
the button flashes for one second.  
Input:AC100-240V~,  
50/60 Hz, 1.1A MAX;  
Output: 9V 1.66 A;  
4 x 1.5V LR6 AA  
- Battery  
8
EN  
 
ChargingVoltage  
and Current  
Operation Power  
Consumption  
Dimensions - Main  
Unit (W x H x D)  
Weight - Main Unit  
5V 1 A  
12 W  
7 Troubleshooting  
Warning  
Never remove the casing of this device.  
201 x 101 x 35 mm  
0.5 kg  
To keep the warranty valid, never try to repair  
the system yourself.  
If you encounter problems when using this  
device, check the following points before  
requesting service. If the problem remains  
unsolved, go to the Philips Web page (www.  
philips.com/support).When you contact Philips,  
make sure that the device is nearby and the  
model number and serial number are available.  
General  
No power  
Make sure that the AC power plug of the  
unit is connected properly.  
Make sure that there is power at the AC  
outlet.  
Insert the batteries with their polarities  
(+/– signs) aligned as indicated.  
Replace the battery.  
No sound  
Adjust volume on the speaker or the  
Bluetooth-connected device.  
Make sure that your Bluetooth device is  
within the effective operational range.  
No response from the unit  
Take out the batteries and turn on the unit  
again.  
Disconnect and reconnect the AC power  
plug, then turn on the unit again.  
Make sure that AC power is connected  
properly.  
Make sure that there is power at the AC  
outlet.  
EN  
9
 
8 Notice  
About Bluetooth device  
The audio quality is poor after connection  
with a Bluetooth-enabled device.  
Any changes or modifications made to this  
device that are not expressly approved by  
WOOX Innovations may void the user’s  
authority to operate the equipment.  
The Bluetooth reception is poor. Move the  
device closer to this product or remove  
any obstacle between them.  
Notice for the USA and Canada  
Cannot connect with the device.  
This device complies with Part 15 of the FCC  
Rules and license-exempt RSS standard of  
Industry Canada. Operation is subject to the  
following two conditions:  
The Bluetooth function of the device is not  
enabled. Refer to the user manual of the  
device for how to enable the function.  
This product is already connected with  
another Bluetooth-enabled device.  
1 this device may not cause harmful  
Disconnect that device and then try again.  
interference, and  
2 this device must accept any interference  
received, including interference that may  
cause undesired operation.  
The paired device connects and disconnects  
constantly.  
The Bluetooth reception is poor. Move the  
device closer to this product or remove  
any obstacle between them.  
This equipment has been tested and found  
to comply with the limits for a Class B digital  
device, pursuant to part 15 of the FCC Rules.  
These limits are designed to provide reasonable  
protection against harmful interference in a  
residential installation.This equipment generates,  
uses, and can radiate radio frequency energy  
and, if not installed and used in accordance  
with the instruction manual, may cause harmful  
interference to radio communications.  
For some devices, Bluetooth connection  
may be deactivated automatically as a  
power-saving feature.This does not indicate  
any malfunction of this product.  
However, there is no guarantee that  
interference will not occur in a particular  
installation. If this equipment does cause harmful  
interference to radio or television reception,  
which can be determined by turning the  
equipment off and on, the user is encouraged  
to try to correct the interference by one or  
more of the following measures:  
Relocate the receiving antenna.  
Increase the separation between  
equipment and receiver.  
Connect the equipment into an outlet on  
a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced  
radio/TV technician for help.  
RF Radiation Exposure Statement: This  
equipment complies with FCC’s and IC’s RF  
10 EN  
 
radiation exposure limits set forth for an  
uncontrolled environment.The antenna(s)  
used for this transmitter must be installed and  
operated to provide a separation distance of  
at least 20 cm from all persons and must not  
be collocated or operating in conjunction with  
any other antenna or transmitter. Installers must  
ensure that 20cm separation distance will be  
maintained between the device (excluding its  
handset) and users.  
packaging materials, exhausted batteries and old  
equipment.  
The Bluetooth® word mark and logos are  
registered trademarks owned by Bluetooth  
SIG, Inc. and any use of such marks by WOOX  
Innovations is under license.  
CAN ICES-3(B)/NMB-3(B)  
Disposal of your old product  
and batteries  
The N Mark is a trademark or registered  
trademark of NFC Forum, Inc. in the United  
States and in other countries.  
Your product is designed and manufactured  
with high quality materials and components,  
which can be recycled and reused.  
Never dispose of your product with other  
household waste. Please inform yourself about  
the local rules on the separate collection of  
electrical and electronic products and batteries.  
The correct disposal of these products helps  
prevent potentially negative consequences on  
the environment and human health.  
Your product contains batteries, which cannot  
be disposed of with normal household waste.  
Please inform yourself about the local rules on  
separate collection of batteries.The correct  
disposal of batteries helps prevent potentially  
negative consequences on the environment and  
human health.  
Please visit www.recycle.philips.com for  
additional information on a recycling center in  
your area.  
Environmental information  
All unnecessary packaging has been omitted.  
We have tried to make the packaging easy to  
separate into three materials: cardboard (box),  
polystyrene foam (buffer) and polyethylene  
(bags, protective foam sheet.)  
Your system consists of materials which can  
be recycled and reused if disassembled by  
a specialized company. Please observe the  
local regulations regarding the disposal of  
EN 11  
 
Specifications are subject to change without notice.  
2014 ©WOOX Innovations Limited.All rights reserved.  
Philips and the Philips’ Shield Emblem are registered  
trademarks of Koninklijke Philips N.V. and are used byWOOX  
Innovations Limited under license from Koninklijke Philips N.V.  
SB365_37_UM_V3.0  
 

Peavey Music Mixer MMA 8150T User Manual
Pelco Home Security System C2403M C User Manual
Philips Car Speaker MMS 231 User Manual
Philips Hair Dryer SJA1184 User Manual
Philips Switch SWV3573 User Manual
Planar Projector PR6022 User Manual
plawa feinwerktechnik GmbH CoKG Digital Camera Nox 13 User Manual
Polk Audio Speaker AMR50 User Manual
Polycom Webcam 1725 22886 001 A User Manual
Poulan Lawn Mower 159515 User Manual