Philips DJ Equipment HTS7111 User Manual

Register your product and get support at  
HTS7111  
EN User manual  
NL Gebruiksaanwijzing  
NO Brukerhåndbok  
DA Brugervejledning  
DE Benutzerhandbuch  
EL Εγχειρίδιο χρήσης  
ES Manual del usuario  
FI Käyttöopas  
PT Manual do utilizador  
SV Användarhandbok  
TR Kullanım kılavuzu  
FR Mode d’emploi  
IT Manuale utente  
 
1 Help and support  
2 Notice  
Watch video tutorials and find answers to many  
frequently answered questions (FAQs) on your  
This section contains the legal and trademark  
notices.  
Compliance  
Tutorials  
To set up your SoundBar and get additional  
information, refer to the video tutorials at www.  
philips.com/support.  
This product is in compliance with the essential  
requirements and other relevant provisions of  
Directives 2006/95/EC (Low Voltage), 2004/108/  
EC (EMC).  
FAQs  
If you have a problem, refer to the frequently  
asked questions (FAQs) for this SoundBar at  
If you still need help, contact Philips Consumer  
Care in your country.  
Mains fuse  
This information applies only to products with a  
UK mains plug.  
This product is fitted with an approved molded  
plug. If you replace the fuse, use one with:  
Warning  
the ratings shown on the plug,  
a BS 1362 approval, and  
the ASTA approval mark.  
Do not attempt to repair your SoundBar  
yourself. This may cause severe injury,  
irreparable damage to your SoundBar, or void  
your warranty.  
Contact your dealer if you are not sure about  
what type of fuse to use.  
Caution:To conform with the EMC directive  
(2004/108/EC), do not detach the plug from the  
power cord.  
Contact Philips  
If you contact Philips, you will be asked for the  
model and serial number of your product. The  
model number and serial number are on the  
back or bottom of your product. Note the  
numbers before you call Philips:  
Model No. __________________________  
Serial No. ___________________________  
4
EN  
 
             
Trademarks  
3 Important  
Read and understand all instructions before you  
use your SoundBar. If damage is caused by failure  
to follow instructions, the warranty does not apply.  
Manufactured under license under U.S. Patent  
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;  
6,487,535 & other U.S. and worldwide patents  
issued & pending. DTS and the Symbol are  
registered trademarks & DTS Digital Surround  
and the DTS logos are trademarks of DTS, Inc.  
Product includes software. DTS, Inc. All Rights  
Reserved.  
Safety  
Risk of electric shock or fire!  
Never expose the product and accessories  
to rain or water. Never place liquid  
containers, such as vases, near the product.  
If liquids are spilt on or into the product,  
disconnect it from the power outlet  
immediately. Contact Philips Consumer  
Care to have the product checked before  
use.  
Manufactured under license from Dolby  
Laboratories. Dolby, Pro Logic, and the  
double-D symbol are trademarks of Dolby  
Laboratories.  
Never place the product and accessories  
near naked flames or other heat sources,  
including direct sunlight.  
Never insert objects into the ventilation  
slots or other openings on the product.  
Where the mains plug or an appliance  
coupler is used as the disconnect device,  
the disconnect device shall remain readily  
operable.  
HDMI, the HDMI logo, and High-Definition  
Multimedia Interface are trademarks or  
registered trademarks of HDMI licensing LLC in  
the United States and other countries.  
Disconnect the product from the power  
outlet before lightning storms.  
When you disconnect the power cord,  
always pull the plug, never the cable.  
Risk of short circuit or fire!  
Before you connect the product to the  
power outlet, ensure that the power  
voltage matches the value printed on the  
back or bottom of the product. Never  
connect the product to the power outlet if  
the voltage is different.  
Risk of injury or damage to the SoundBar!  
For wall-mountable products, use only the  
supplied wall mount bracket. Secure the  
wall mount to a wall that can support the  
combined weight of the product and the  
wall mount. Koninklijke Philips Electronics  
N.V. bears no responsibility for improper  
wall mounting that results in accident, injury  
or damage.  
Never place the product or any objects  
on power cords or on other electrical  
equipment.  
EN  
5
 
     
If the product is transported in  
Care for your product  
temperatures below 5°C, unpack the  
product and wait until its temperature  
matches room temperature before  
connecting it to the power outlet.  
Parts of this product can be made of  
glass. Handle with care to avoid injury and  
damage.  
Use only microfiber cloth to clean the product.  
Care of the environment  
Risk of overheating!  
Never install this product in a confined  
space. Always leave a space of at least four  
inches around the product for ventilation.  
Ensure curtains or other objects never  
cover the ventilation slots on the product.  
Your product is designed and manufactured with  
high quality materials and components, which  
can be recycled and reused.  
Risk of contamination!  
Do not mix batteries (old and new or  
carbon and alkaline, etc.).  
Remove batteries if they are exhausted or  
if the remote control is not to be used for a  
long time.  
Batteries contain chemical substances, they  
should be disposed of properly.  
When this crossed-out wheeled bin symbol is  
attached to a product it means that the product  
is covered by the European Directive 2002/96/  
EC. Please inform yourself about the local  
separate collection system for electrical and  
electronic products.  
Please act according to your local rules and  
do not dispose of your old products with your  
normal household waste.  
Risk of swallowing batteries!  
The product/remote control may contain a  
coin type battery, which can be swallowed.  
Keep the battery out of reach of children at  
all times!  
Correct disposal of your old product helps to  
prevent potential negative consequences for the  
environment and human health.  
Your product contains batteries covered by the  
European Directive 2006/66/EC, which cannot  
be disposed with normal household waste.  
Please inform yourself about the local rules on  
separate collection of batteries because correct  
disposal helps to prevent negative consequences  
for the environmental and human health.  
6
EN  
 
   
Remote control  
4 Your SoundBar  
Congratulations on your purchase, and welcome  
to Philips!To fully benefit from the support that  
Philips offers, register your SoundBar at www.  
philips.com/welcome.  
2
3
Main unit  
14  
1
2
3
4
5
13  
6
4
7
8
9
a SOURCE  
Select an audio source for the SoundBar.  
b
(Standby-On)  
Switch the SoundBar on or to standby.  
When the SoundBar is in standby, the  
standby indicator turns red.  
10  
11  
c
+/- (Volume)  
Increase or decrease volume.  
d Display panel  
12  
a
(Standby-On)  
Switch the SoundBar on or to standby.  
When EasyLink is enabled, press  
and hold for at least three seconds  
to switch all connected HDMI CEC  
compliant devices to standby.  
EN  
7
 
     
b HDMI SOURCE  
EasyLink controls  
Switch your audio source to the HDMI  
connection.  
With Easylink, you can control your SoundBar,  
TV and the connected devices with the standby  
button on your SoundBar remote control.  
c DOCK for iPod  
Switch to Philips dock for iPod or iPhone.  
(Standby-On): Press and hold to switch  
your SoundBar, TV, and the connected  
devices to standby.  
d Navigation buttons (  
/
/
/
)
Navigate menus.  
e OK  
Confirm an entry or selection.  
f
SOUND SETTINGS  
Access or exit sound options.  
g Dock for iPod/iPhone buttons  
(Stop)/EXIT: Stop play for iPod or  
iPhone, or exit the SoundBar setup  
menu.  
/
(Previous/Next): Skip to the  
previous or next track or file. Press and  
hold to search backwards or forwards.  
(Play/Pause): Start, pause, or  
resume play. Press and hold to switch  
off the iPod or iPhone.  
Navigation button ( ): Return to the  
previous menu on the iPod or iPhone,  
or return to the previous SoundBar  
menu.  
h
(Mute)  
Mute or restore volume.  
i +/- (Volume)  
Increase or decrease volume.  
j TREBLE +/-  
Increase or decrease treble.  
k BASS +/-  
Increase or decrease bass.  
l AMBISOUND  
Select an Ambisound, auto or stereo mode.  
m SETUP  
Access the setup menu.  
n AUDIO SOURCE  
OPTI IN: Switch your audio source to  
the optical connection.  
COAX IN: Switch your audio source  
to the coaxial connection.  
AUX: Switch your audio source to the  
AUX connection.  
MUSIC iLINK: Switch your audio  
source to the MUSIC iLINK  
connection.  
8
EN  
 
Connect  
5 Connect your  
SoundBar  
Connect your subwoofer to your SoundBar as  
described in the quick start guide.  
This section helps you connect your SoundBar to a  
TV and other devices.  
Setup  
For information about the basic connections of  
your SoundBar and accessories, see the quick start  
guide. For a comprehensive interactive guide, see  
Set up your subwoofer through the setup menu.  
1
VOL on the display panel (see ‘Setup menu  
options and settings’ on page 18).  
2
3
Press OK.  
Note  
Press the Navigation buttons (  
change the volume.  
/
) to  
For identification and supply ratings, refer to  
the type plate at the back or bottom of the  
product.  
Before you make or change any connections,  
make sure that all devices are disconnected  
from the power outlet.  
4
5
Press OK to confirm.  
Press EXIT to exit the menu.  
Connectors  
Connect other devices to your SoundBar.  
Subwoofer  
Side left  
Follow the steps below to position, connect, and  
set up your subwoofer.  
Position  
M
i
L
U
I
N
S
K
Place the subwoofer at least one meter (three  
feet) away from either to the left or right of your  
SoundBar, and ten centimeter away from the  
wall.  
I
C
For best results, place your subwoofer as shown  
below.  
MUSIC iLINK  
Audio input from an MP3 player.  
Rear left  
AC MAINS~  
AC MAINS~  
Connect to the power supply.  
EN  
9
 
     
Rear center  
Connect toTV  
Connect your SoundBar to aTV.You can listen to  
audio fromTV programs through your SoundBar.  
Use the best quality connection available on your  
SoundBar andTV.  
COAXIAL  
DIGITAL IN  
6
5
HDMI IN  
OPTICAL  
1
2
L
(WHITE)  
AUDIO IN-AUX  
4
3
Option 1: Connect toTV through HDMI  
(ARC)  
R
(RED)  
HDMI OUT (ARC)  
TO TV  
DOCK for iPod  
Your SoundBar supports HDMI version 1.4  
- Audio Return Channel (ARC). If your TV is  
HDMI ARC compliant, connect your SoundBar  
to the TV through the HDMI ARC connection.  
a HDMI IN 1/2  
With HDMI ARC, you do not need an additional  
audio cable to play audio from TV through your  
SoundBar.  
Connect to the HDMI output on the audio  
devices.  
1
Using a High Speed HDMI cable, connect  
the HDMI OUT (ARC) connector on your  
SoundBar to the HDMI ARC connector on  
the TV.  
The HDMI ARC connector on the TV  
might be labeled HDMI IN or HDMI. For  
details on TV connectors, see the TV user  
manual.  
b TO TV-HDMI OUT (ARC)  
Connect to the HDMI input on the TV.  
c DOCK for iPod  
Connect to a Philips dock for iPod or  
iPhone.(Model: Philips DCK3060).  
d AUDIO IN-AUX  
Connect to an analog audio output on the  
TV or an analog device.  
e DIGITAL IN-OPTICAL  
Connect to an optical audio output on the  
TV or a digital device.  
TV  
f DIGITAL IN-COAXIAL  
Connect to a coaxial audio output on the  
TV or a digital device.  
Rear right  
2
3
On your TV, turn on HDMI-CEC. For  
details, see the TV user manual.  
» The audio from theTV is automatically  
played on your Soundbar.  
SUBWOOFER (6Ω)  
If audio from the TV does not play  
automatically, select the correct video input  
on the TV.  
SUBWOOFER  
Connect to the supplied subwoofer.  
10 EN  
 
   
Option 2: Connect toTV through an  
analog audio cable  
TV  
If your TV does not have HDMI connectors,  
connect your SoundBar to the TV through an  
analog audio cable connection.  
1
Using an analog cable, connect AUX  
connectors on your SoundBar to the audio  
connectors on the TV.  
TV  
2
3
Select the correct video input on your TV.  
to a connected device’ on page 13).  
Connect to other devices  
through HDMI  
2
3
Using another High Speed HDMI cable,  
connect the HDMI OUT (ARC) connector  
on your SoundBar to the HDMI IN or  
HDMI ARC connector on the TV.  
Connect digital devices directly to your SoundBar  
through an HDMI connection. Digital devices  
can include a Blu-ray player, set-top box, games  
console, or camcorder.  
On the connected devices, turn on HDMI-  
CEC. For details, see the user manual of the  
devices.  
4
5
Select the correct video input on the TV.  
1
Using a High Speed HDMI cable, connect  
the HDMI OUT connector on your digital  
device to the HDMI IN connector on your  
SoundBar.  
SoundBar (see ‘Set up audio for connected  
devices’ on page 13).  
Note  
If you connect the HDMI OUT (ARC)  
connector on your SoundBar to an HDMI ARC  
compliant TV, you can either choose to select  
the audio to output through your SoundBar or  
through the TV. For details about mapping the  
TV audio, see the TV user manual.  
EN 11  
 
 
Option 2: Connect audio through a digital  
coaxial cable  
Connect audio fromTV and  
other devices  
Good quality audio  
Using a coaxial cable, connect the COAXIAL  
connector on your SoundBar to the COAXIAL/  
DIGITAL OUT connector on the device.  
Play audio fromTV or other devices through your  
SoundBar.  
Use the best quality connection available on other  
devices.  
The digital coaxial connector might be labeled  
DIGITAL AUDIO OUT.  
Note  
The audio connections in this user manual are  
only recommendations. You can use other  
connections too.  
When your SoundBar and TV are connected  
through HDMI ARC, an audio connection is  
not required.  
Option 1: Connect audio through a digital  
optical cable  
Tip  
Best quality audio  
To play video from the device, connect the  
device to the TV through a video connection.  
Using an optical cable, connect the OPTICAL  
connector on your SoundBar to the OPTICAL  
OUT connector on the device.  
The digital optical connector might be labeled  
SPDIF, SPDIF OUT, or OPTICAL.  
Option 3: Connect audio through analog  
audio cables  
Basic quality audio  
Using an analog cable, connect the AUX  
connectors on your SoundBar to the audio  
connectors on the device.  
TV  
VCR  
Tip  
To play video from the device, connect the  
device to the TV through a video connection.  
12 EN  
 
 
Set up audio for connected devices  
Listen to a connected device  
When you connect a device to your SoundBar,  
check the audio settings.  
Before you can listen to a connected device, select  
the source for the device.  
Main unit  
Press SOURCE on the SoundBar to cycle  
through and select one of the following audio  
sources on the display panel:  
HDMI ARC (if avaliable) > HDMI IN1 > HDMI  
IN2 > MUSIC I-LINK > IPOD > AUX > OPTI  
IN > COAX IN  
1
On your TV and other devices, turn on  
HDMI-CEC. For details, see the user  
manual of the TV and the other device.  
2
3
Select ‘Amplifier’ from the TV speakers  
menu. For details, see the TV user manual.  
on your SoundBar (see ‘Play audio from  
SoundBar’ on page 17).  
Remote control  
Press AUDIO SOURCE or HDMI SOURCE on  
the remote control to cycle through and select  
an audio source, as shown in the following table.  
audio input on your SoundBar (see ‘Listen to a  
connected device’ on page 13).  
Source button  
Display text  
Audio  
source  
AUDIO SOURCE OPTI IN  
AUDIO SOURCE COAX IN  
AUDIO SOURCE AUX  
Optical  
input  
Coaxial  
input  
AUX input  
MP3 input  
AUDIO SOURCE MUSIC  
I-LINK  
HDMI SOURCE  
HDMI ARC (if HDMI  
available)  
ARC  
output  
HDMI SOURCE  
HDMI IN1 or HDMI  
HDMI IN2 input  
Note  
‘Option 1: Connect to TV through HDMI  
(ARC)’ on page 10).  
EN 13  
 
   
Sound mode  
6 Use your SoundBar  
Select predefined sound modes to suit your  
video or music.  
This section helps you use the SoundBar to play  
audio from connected devices.  
Before you start  
1
‘Sound options and settings’ on page 14).  
Make the necessary connections described  
in the quick start guide and the user manual.  
Switch the SoundBar to the correct source  
for other devices.  
2
3
Select a mode, and then press OK.  
Press the Navigation buttons (  
select a setting:  
/
) to  
AUTO: Select either MOVIE or  
MUSIC automatically depend on the  
sound stream.  
MOVIE: Enjoy a cinematic audio  
experience, specially enhanced for  
movies.  
MUSIC: Recreate the original recording  
environment of your music, in the  
studio or at a concert.  
ORIGINAL: Experience the original  
sound of your movies and music,  
without added sound effects.  
NEWS: Hear every word with  
optimized speech and clear vocals.  
GAMING: Enjoy thrilling arcade  
sounds, ideal for action-packed video  
games or loud parties.  
Choose your sound  
This section helps you choose the ideal sound for  
your video or music.  
Sound options and settings  
Sound  
option  
Setting for the option  
MODE  
AUTO  
MOVIE  
MUSIC  
ORIGINAL  
NEWS  
GAMING  
ON  
AUTO  
VOL  
Auto volume  
OFF  
Turn the auto volume on to keep the volume  
constant when you switch to a different source.  
NIGHT  
ON  
OFF  
1
‘Sound options and settings’ on page 14).  
AUD  
SYNC  
0 MS, 10 MS, 20 MS, ..., 180 MS,  
190 MS, 200 MS  
2
3
Press OK.  
1
panel (see ‘Sound options and settings’ on  
page 14).  
Press the Navigation buttons (  
select a setting:  
/
) to  
ON: Turn on auto volume.  
OFF: Turn off auto volume.  
2
3
Select a setting, and then press OK.  
Press the Navigation buttons (  
/
) to  
select an option.  
4
Press EXIT to exit.  
If you do not press a button within ten seconds,  
the menu exits automatically.  
14 EN  
 
     
Night mode  
Equalizer  
For quiet listening, decrease the volume of loud  
sounds when you play discs. Night mode is only  
available for Dolby encoded DVD and Blu-ray  
discs.  
Change the high frequency (treble) and low  
frequency (bass) settings of the SoundBar.  
Press TREBLE +/- or BASS +/- to change the  
frequency shown on the display panel.  
1
‘Sound options and settings’ on page 14).  
MP3 player  
2
3
Press OK.  
Connect your MP3 player to play your audio files  
or music.  
What you need  
Press the Navigation buttons (  
select a setting:  
/
) to  
ON: Turn on night mode.  
OFF: Turn off night mode.  
An MP3 player.  
A 3.5mm stereo audio cable.  
Note  
Play music  
If auto volume is set to ON, you cannot enable  
the night mode.  
1
2
3
Connect the MP3 player to the SoundBar as  
described in the Quick start guide.  
Press AUDIO SOURCE repeatedly to  
select MUSIC I-LINK on the display panel.  
Synchronize picture and sound  
Press the buttons on the MP3 player to  
select and play audio files or music.  
If the audio and video are not synchronized,  
delay the audio to match the video.  
1
‘Sound options and settings’ on page 14).  
iPod or iPhone  
When you connect a Philips dock for iPod/iPhone,  
you can use the SoundBar to play music, movies  
and photos from your iPod or iPhone.  
2
3
Press OK.  
Within two seconds, press the Navigation  
buttons (  
shown on the display panel.  
/
) to change the delay  
What you need  
A Philips dock (Model: Philips DCK3060).  
A yellow composite cable.  
4
Press OK to confirm.  
Note  
Ambisound  
Set up Ambisound to give the best surround  
sound effect.  
Press AMBISOUND repeatedly to select a  
Philips dock for iPod or iPhone is sold  
separately.  
Charge your iPod or iPhone on the dock while  
the SoundBar is in iPod mode.  
setting on the display panel:  
room (see ‘Ambisound’ on page 18).  
STEREO: Two-channel stereo sound. Ideal  
for listening to music.  
AUTO: Surround sound based on the audio  
stream.  
Dock your iPod or iPhone  
1
Move the slide at the bottom of the dock to  
STANDARD, and then connect the dock to  
the SoundBar.  
2
3
Connect the yellow composite cable to the  
dock and TV.  
Note  
If you play a source with DTS, DTS is displayed  
on the display panel for two seconds.  
If you play a source with Dolby, DOLBY D is  
displayed on the display panel for two seconds.  
Switch on the iPod or iPhone, and place it  
on the dock.  
EN 15  
 
     
Play music  
EasyLink  
1
2
Dock your iPod or iPhone (see ‘Dock your  
iPod or iPhone’ on page 15).  
The SoundBar supports Philips EasyLink, which  
uses the HDMI-CEC (Consumer Electronics  
Control) protocol. EasyLink-compliant devices that  
are connected through HDMI can be controlled  
by a single remote control.  
Philips does not guarantee 100% interoperability  
with all HDMI-CEC devices.  
Press DOCK for iPod.  
» IPOD appears on the display panel.  
3
Press the play buttons to control play.  
Button  
Navigation  
buttons (  
Action  
What you need  
Navigate up and down the  
menus.  
HDMI-CEC compliant devices.  
An HDMI connection between the  
connected devices.  
/
)
OK  
Confirm an entry or selection.  
Skip to the previous or next  
track or file. Press and hold to  
search backwards or forwards.  
/
Switch on  
(Previous/  
Next)  
1
Switch on the HDMI-CEC operations on  
Start, pause, or resume play.  
Press and hold to switch off the  
iPod or iPhone.  
(Play/  
the TV and other connected devices. For  
information, see the manual of the TV or  
other devices.  
Pause)  
Stop play for iPod or iPhone, or  
exit the SoundBar setup menu.  
2
menu options and settings’ on page 18).  
(Stop)/EXIT  
Navigation  
Return to the previous menu on  
the iPod or iPhone, or return to  
the previous SoundBar menu.  
button (  
)
3
4
Press OK.  
Press the Navigation buttons (  
select ON.  
/
) to  
5
Press OK to confirm.  
» The EasyLink is on.  
Play video and slideshows  
1
2
On iPod, enable the TV ON setting. On  
iPhone, select the TV Out option.  
Note  
Dock your iPod or iPhone (see ‘Dock your  
iPod or iPhone’ on page 15).  
To disable EasyLink, select OFF.  
When EasyLink is switched off, the following  
options are not available: SYS STBY, AUD  
CTRL, and TV AUDIO.  
3
4
Press DOCK for iPod.  
Switch the TV to the AV/VIDEO source  
(corresponding to the yellow composite  
cable).  
» TheTV screen goes blank.  
5
6
Browse on the iPod or iPhone screen to  
select videos or photos.  
Press  
(Play/Pause) on the SoundBar  
remote control to play the videos or  
photos.  
» The picture is displayed on theTV.  
16 EN  
 
   
Control devices  
Play audio from SoundBar  
Control the SoundBar and the other connected  
HDMI-CEC compliant devices with a single  
remote control.  
You need to connect an HDMI-CEC device to  
the TV and route its audio output from TV to  
the SoundBar in order to map the audio of the  
connected device to your SoundBar.  
One-touch standby  
1
CTRL on the display (see ‘Setup menu  
options and settings’ on page 18).  
When you press and hold (Standby) on  
the remote control, the SoundBar and all the  
connected HDMI-CEC devices (that support  
one-touch standby) switch to the standby  
mode.  
If One-touch standby is enabled on your  
SoundBar, you can switch to standby with the  
remote control of the TV or other connected  
HDMI-CEC devices.  
2
3
Press OK.  
Press the Navigation buttons (  
/
) to  
select ON, and then press OK.  
To play the audio from the TV  
speakers, select OFF.  
Press SETUP repeatedly to select TV  
4
5
AUDIO on the display panel, and then press  
OK.  
System Audio Control  
You need to connect a device to the TV  
and route its audio output from TV to the  
SoundBar so that the SoundBar can switch to  
the corresponding audio source automatically.  
To use one-touch audio, switch on System  
Audio Control and map connected devices to  
the audio input connectors of the SoundBar.  
Press the Navigation buttons (  
/
) to  
select the audio output for each connected  
device.  
HDMI ARC: Audio output through the  
HDMI ARC connection.  
COAX IN: Audio output through the  
coaxial connection.  
OPTI IN: Audio output through the  
optical connection.  
AUX: Audio output through the AUX  
connection.  
TV Audio Mapping  
audio input connector (see ‘Play audio from  
SoundBar’ on page 17).  
6
7
Press OK to confirm.  
Press EXIT to exit the menu.  
One-touch standby  
Note  
The SoundBar and all connected HDMI-CEC  
devices can be switched to standby by a remote  
control.  
(see ‘Option 1: Connect to TV through HDMI  
(ARC)’ on page 10).  
1
STBY on the display panel (see ‘Setup menu  
options and settings’ on page 18).  
2
3
Press OK.  
Press the Navigation buttons (  
select ON.  
/
) to  
4
5
Press OK to confirm.  
Press EXIT to exit the menu.  
Note  
To disable One-touch standby, select OFF.  
EN 17  
 
 
1
menu options and settings’ on page 18).  
7 Change settings  
This section helps you to change the settings of  
your SoundBar.  
2
3
Select an option, and then press OK.  
Press the Navigation buttons (  
/
) to  
select a setting for the option, and then  
press OK.  
Caution  
Most of the settings are already configured  
with the best value for your SoundBar. Unless  
you have a reason to change a setting, it is best  
to leave it at the default value.  
Note  
If you do not press a button within ten  
seconds, the setup menu exits.  
To return to the previous menu, press the  
Navigation button ( ). To exit the menu,  
press EXIT.  
Setup menu options and  
settings  
Setup menu  
option  
EASYLINK  
Setting for the  
option  
ON  
OFF  
ON  
OFF  
ON  
OFF  
HDMI ARC  
COAX IN  
OPTI IN  
AUX  
+5, +4, +3, ..., 0, ...,  
-3, -4, -5  
Setting for  
the option  
Ambisound  
To give the best surround sound effect, select  
options about your room and the position of the  
SoundBar.  
SYS STBY  
1
‘Setup menu options and settings’ on page  
18).  
AUD CTRL  
TV AUDIO  
2
3
Press OK.  
Set the position of the SoundBar.  
A Press the Navigation buttons (  
/
) to select POSITION, and then press  
OK.  
SUBW VOL  
B Press the Navigation buttons (  
/
)
to select IN FRONT, RIGHT, LEFT, or  
AMBISOUND POSITION  
IN  
FRONT  
CORNER, and then press OK.  
4
Set the distance between your listening  
position and the SoundBar.  
RIGHT  
LEFT  
CORNER  
0M - 2M  
2M - 3M  
A Press the Navigation buttons (  
/
) to select DISTANCE, and then press  
DISTANCE  
OK.  
B Press the Navigation buttons (  
/
) to select 0M - 2M (from zero to two  
meters), 2M - 3M (from two to three  
meters), or ABOVE 3M (above three  
meters), and then press OK.  
ABOVE  
3M  
DISPLAY  
BRIGHT  
DIM 1  
DIM 2  
18 EN  
 
     
Display panel  
8 Wall mount and  
stand  
‘Safety’ on page 5).  
Change the brightness of the SoundBar display  
panel.  
1
on the display panel (see ‘Setup menu  
options and settings’ on page 18).  
2
3
Press OK.  
If you have any query, contact Philips Consumer  
Care in your country.  
Press the Navigation buttons (  
select BRIGHT, DIM 1, or DIM 2, and then  
/
) to  
press OK.  
Wall mount  
Apply factory settings  
Screw length/diameter  
Depend on the type of wall mounting this wall  
mount bracket, make sure that you use screws of a  
suitable length and diameter.  
You can reset your SoundBar to the default  
settings programmed at the factory.  
In AUX mode, within three seconds, press  
TREBLE+, VOL-, and BASS+.  
» When the factory settings restore is  
complete, the SoundBar automatically  
switches off and restarts.  
3 - 3.5mm  
> 25mm  
Note  
Before wall mount, you can remove the three  
rubber feet at the bottom of the SoundBar.  
If you remove the rubber feet, you cannot stick  
them back on the bottom of the SoundBar.  
For information about how to wall your SoundBar,  
see the wall mount guide.  
EN 19  
 
     
Stand for SoundBar andTV -  
STS1100/STS1300  
9 Product  
specifications  
If you have a PhilipsTV, you can mount your  
SoundBar and theTV onto a single stand.  
Note  
Purchase the STS1100 or STS1300 stand from an  
authorized Philips dealer.  
For instructions on how to install the stand with  
the SoundBar and PhilipsTV, see the stand quick  
start guide.  
Specifications and design are subject to change  
without notice.  
Amplifier  
STS1100:  
Total output power:  
Europe and Asia: 300W RMS (30%  
THD)  
Latin America: 224W RMS (10% THD)  
Frequency response: 20 Hz-20 kHz / ±3 dB  
Signal-to-noise ratio: > 65 dB (CCIR) /  
(A-weighted)  
Input sensitivity:  
AUX: 250 mV  
Music iLink: 50 mV  
Audio  
S/PDIF Digital audio input:  
Coaxial: IEC 60958-3  
Optical: TOSLINK  
Main unit  
STS1300:  
Power supply: 110-240 V~, 50-60 Hz  
Power consumption: 55 W  
Standby power consumption: ≤ 1 W  
Center speaker:  
Speaker impedance: 6 ohm  
Speaker drivers: 2 x 64 mm (2.5”) full  
range  
Frequency response: 150 Hz-20 kHz  
Front/Rear speakers:  
Speaker impedance: 3 ohm  
Speaker drivers: 4 x 64 mm (2.5”) full  
range  
Frequency response: 150 Hz-20 kHz  
Dimensions (WxHxD): 945 x 108 x 86 mm  
Weight: 3.82 kg  
20 EN  
 
   
Subwoofer  
10 Troubleshooting  
Output power: 80W RMS (30% THD)  
Impedance: 6 ohm  
Speaker drivers: 165 mm (6.5”) woofer  
Frequency response: 20 Hz-150 Hz  
Dimensions (WxHxD): 192 x 447 x 253  
mm  
Warning  
Risk of electric shock. Never remove the  
casing of the product.  
Weight: 4.4 kg  
Cable length: 3 m  
To keep the warranty valid, never try to repair the  
product yourself.  
If you have problems using this product, check the  
following points before you request service. If you  
still have a problem, register your product and get  
Wall mount  
Dimensions (WxHxD): 80 x 80 x 15 mm  
Weight: 0.08 kg/each  
Main unit  
Remote control batteries  
The buttons on the SoundBar do not work.  
2 x AAA-R03-1.5 V  
Disconnect the SoundBar from the power  
supply for a few minutes, then reconnect.  
Sound  
No sound from SoundBar speakers.  
Connect the audio cable from your  
SoundBar to your TV or other devices.  
However, you do not need a separate audio  
connection when:  
the SoundBar and TV are connected  
through HDMI ARC connection, or  
a device is connected to the HDMI IN  
connector on your SoundBar.  
(see ‘Set up audio for connected devices’ on  
page 13).  
(see ‘Apply factory settings’ on page 19), and  
then switch it off and switch on again.  
On your SoundBar, press SOURCE  
repeatedly to select the correct audio input  
on the display panel.  
Make sure that the SoundBar is not muted.  
Press to select MUTE OFF on the display  
panel.  
Distorted sound or echo.  
If you play audio from the TV through the  
SoundBar, make sure that the TV is muted.  
Audio and video are not synchronized.  
1) Press SOUND SETTINGS repeatedly  
to select AUD SYNC on the display panel,  
and then press OK. 2) Within two seconds,  
press the Navigation buttons (  
/
)
to change the delay shown on the display  
panel. 3) Press OK to confirm.  
EN 21  
 
 
Play  
When you switch on theTV, the SoundBar  
automatically switches on.  
This behavior is normal when you are using  
Philips EasyLink (HDMI-CEC). To make the  
SoundBar work independently, switch off  
EasyLink.  
EasyLink does not work.  
on’ on page 16).  
Cannot play video or photos from an iPod or  
iPhone on theTV.  
Browse and select videos and photos from  
the iPod or iPhone screen, and play them  
on your TV.  
Make sure that the iPod or iPhone software  
has not been tampered with or illegally  
modified.  
Cannot view pictures from an iPod or iPhone on  
theTV.  
Connect a yellow composite cable to the  
iPod dock and the TV.  
Switch the TV to the AV/VIDEO source  
(corresponding to the yellow composite  
cable).  
Press the play button on the iPod or iPhone  
to start a slideshow.  
Make sure that the iPod or iPhone software  
has not been tampered with or illegally  
modified.  
22 EN  
 
© 2011 Koninklijke Philips Electronics N.V.  
All rights reserved.  
sgptt_1131/12_v2  
 

Pelco Home Security System C3610m a1 08 User Manual
Philips Computer Monitor 107S77 User Manual
Philips Digital Camera SPZ3000 User Manual
Philips Flat Panel Television 17PF9945 58 User Manual
Philips Speaker System MMS 305 User Manual
Philips Universal Remote PL1IRR User Manual
Pioneer Headphones SE NC31C K User Manual
Poulan Lawn Mower 182705 User Manual
Powermate Portable Generator PM0435002 User Manual
Precisionaire Air Cleaner PB1900 0604 User Manual