Planar Computer Monitor PQ1910M User Manual

PQ1910M  
LCD Monitor  
USER’S GUIDE  
 
The information contained in this document is subject to change without notice. This  
document contains proprietary information that is protected by copyright. All rights are  
reserved. No part of this document may be reproduced, translated to another language or  
stored in a retrieval system, or transmitted by any means, electronic, mechanical,  
photocopying, recording, or otherwise, without prior written permission. Windows is a  
registered trademark of Microsoft Inc. Other brand or product names are trademarks of  
their respective holders.  
3
 
4
 
TABLE OF CONTENTS  
FOR YOUR SAFETY  
For Your Safety -------------------------------------------------------------------------------------6  
GENERAL NOTES  
1. Introduction--------------------------------------------------------------------------------------8  
1.1 General Information  
1.2 Features  
1.3 Check List  
2. Installation --------------------------------------------------------------------------------------9  
2.1 Installing the base  
2.2 Installing the monitor  
2.3 Self test pattern  
2.4 Adjusting picture  
3. Operation of the Monitor -----------------------------------------------------------------11  
3.1 Power on/off switch  
3.2 Power LED indicator  
3.3 OSD control keys  
3.4 Safety mode  
3.5 Timing guide  
3.6 Plug & Play  
3.7 Power management  
3.8 Volume adjust  
4. Specifications ---------------------------------------------------------------------------------17  
5. Simple Troubleshooting -------------------------------------------------------------------18  
5
 
FOR YOUR SAFETY  
Before operating the monitor, please read this manual thoroughly. This manual should be  
retained for future reference.  
FCC Class B Radio Frequency Interference Statement  
WARNING: (FOR FCC CERTIFIED MODELS)  
NOTE: This equipment has been tested and found to comply with the limits for a Class B  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy, and if not installed and  
used in accordance with the instructions, may cause harmful interference to radio  
communications.  
However, there is no guarantee that interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio or television reception, which can  
be determined by turning the equipment off and on, the user is encouraged to try to correct  
the interference by one or more of the following measures:  
1. Reorient or relocate the receiving antenna.  
2. Increase the separation between the equipment and receiver.  
3. Connect the equipment into an outlet on a circuit different from that to which the receiver  
is connected.  
4. Consult the dealer or an experienced radio/TV technician for help.  
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE  
RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR  
FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE ELECTRONIC  
INDUSTRIES ALLIANCE AT WWW.EIAE.ORG. FOR LAMP SPECIFIC  
DISPOSAL INFORMATION CHECK WWW.LAMPRECYCLE.ORG.  
NOTICE:  
1. The changes or modifications not expressly approved by the party responsible for  
compliance could void the user's authority to operate the equipment.  
2. Shielded interface cables and AC power cord, if any, must be used in order to comply  
with the emission limits.  
3. The manufacturer is not responsible for any radio or TV interference caused by  
unauthorized modification to this equipment. It is the responsibilities of the user to  
correct such interference.  
WARNING:  
To prevent fire or shock hazard, do not expose the monitor to rain or moisture.  
Dangerously high voltages are present inside the monitor. Do not open the  
cabinet. Refer servicing to qualified personnel only.  
6
 
PRECAUTIONS  
1. Unplug the monitor from the power source when you clean the monitor. Do  
not use liquid cleaners or aerosol cleaners. Use a cloth to clean it. If that  
doesn’t do, please use LCD screen cleaners.  
2. Do not use attachment not recommended as they may cause hazards.  
3. Please grasp the plug to unplug the connector from the wall outlet. Do not pull  
the power cord to unplug it.  
4. Do not place anything on the power cord or step on it  
5. Do not place the monitor near water such as bathtub, washbowl, sink, laundry  
tub, swimming pool etc.  
6. The slots are designed for ventilation they keep the monitor both workable  
and protect it from overheating. For the same reason, please do not place the  
monitor on a bed, sofa, carpets or other similar surface. Do not place the  
monitor near or over a heat source, or place in a enclosed structure/area.  
7. Keep the monitor at least 2 inches (5 cm) away from the wall or other goods.  
8. This monitor can only use the power source indicated on the label. If you  
have questions, please consult your dealer.  
9. As a safety measure, this monitor is equipped with a three-wire ground style  
plug. If you can not insert the plug into outlet, contact your electrician to install  
the correct outlet, or use an adapter to ground the appliance safely. Do not  
bypass the safety purpose of the grounding-type plug.  
10. Please make sure that the outlet and power cord can support the total  
electricity use of the products.  
11. Place the monitor in safe place where the cord will not be easily tripped over.  
12. Follow all the warnings and instructions illustrated in the manual.  
13. Don’t overload the wall outlets and extension cords as this can result in fire or  
electric shocks.  
14. Do not remove or open the cover to service this monitor yourself. It may  
expose you to dangerous voltage or other hazards. Please refer all servicing  
to qualified service personnel.  
15. Unplug this monitor from the outlet and refer servicing to qualified service  
personnel under the following conditions.  
A.  
B.  
C.  
The power cord is frayed or damaged.  
The monitor has been dropped or the cabinet has been damaged  
When the monitor displays a distinct change in performance, this  
indicates a need for service.  
16. The power cord is the main device to disconnect the power.  
17. Unplug the power cord when you do not use the monitor for a long time.  
18. Place the monitor in a well ventilated area and protect it from strong light,  
overheating and moisture.  
19. This monitor must be stored in a room in between the temperature of –20°C ~  
+55°C. Storing outside this range may cause permanent damage.  
7
 
GENERAL NOTES  
1.Introduction  
1.1 General Information  
This monitor is a high-performance intelligent multi-scanning color monitor  
utilizing active matrix TFT LCD display that uses amorphous silicon TFT as a  
switching device. With very low radiation, anti-glare surface treatment and small  
footprint, it is very suitable for home and office applications.  
1.2 Features  
LCD TFT 19" monitor  
Built-in multimedia speakers  
Multi-language OSD interface  
Auto adjusting imaging  
White and black reference voltage auto-calibration  
Compliant with EPA energy star, VESA DPMS  
Plug & Play  
1.3 Check List  
Check the list before operating this monitor. Please make sure that all of the  
following items are included.  
LCD monitor  
Base + mounting screw  
AC adapter  
Power cord  
VGA Signal cable  
DVI cable  
Audio cable  
User’s manual  
If any of the above listed items are missing, please contact your dealer for  
technical support or customer service.  
8
 
2. Installation  
The following chapters explain how to install the base and connect the monitor to  
your personal computer.  
2.1 Installing the Base  
Follow these steps to install the base:  
1. Lay the monitor face down.  
2. Assemble the base to the arm with screw.  
3. Tighten the screw with a coin.  
2.2 Installing the Monitor  
Before starting, make sure that the computer and monitor’s power are both turned  
off. Please follow the steps to install your LCD monitor:  
1. Signal cable connection: Plug one end of the signal cable into computer and  
lock the two bolts. Then plug the other end into the monitor and lock the two  
bolts. Make sure connections are secure.  
2. Power cord connection: connect the AC adapter with the DC power cord.  
Next connect the AC adapter output to the power input of the monitor. Then  
connect the DC power cord to an electrical outlet.  
3. Audio cable connection: Insert one end of the audio cable to the audio output  
of the PC audio card and the other to the audio input of LCD monitor.  
4. Power on: turn on both the monitor and computer. After the monitor is  
powered on, the LED lights up green, If the LED starts flashing red, please  
check the video signal cable. If LED is off, please press power on switch.  
9
 
2.3 Self Test Pattern  
If there is no horizontal or vertical signal, your monitor will display the self test  
pattern to indicate no signal input. After a few seconds, the monitor will enter into  
waiting and saving power mode. The LED will be red and flashing. Once the  
monitor receives the video signal, it will return to normal mode.  
2.4 Adjusting Picture  
In order to obtain the best visual display, you must adjust it, please refer to  
chapter 3 “Operation of the monitor”.  
10  
 
3. Operation of the Monitor  
3.1 Power On/Off Switch  
This is a light-touch digital-control key. It is used to turn the monitor on or off.  
3.2 Power LED Indicator  
When the monitor is working, the power LED is green. If the monitor is in saving  
power mode, the power LED will be red and flashing. If you turn off the computer,  
the power LED is off. When the LED is off, the monitor is off, but the power  
adapter is on. For added safety, you should unplug the power adapter when you  
don’t use the monitor for an extended period of time.  
3.3 OSD Control Keys  
3.3.1 Auto Key  
This key is used to complete auto adjusting function in VGA mode.  
3.3.2 +/- Key  
These two keys will complete the right (increase) or left (decrease) adjustment  
and choose the menu function. The volume can be set by +/- key directly.  
3.3.3 Enter Key  
Activates the OSD menu and acts as an enter function.  
3.3.4 OSD Menu  
The function list of the menu:  
1. Auto adjustment  
2. Brightness  
3. Contrast  
4. H-position  
5. V-position  
6. Clock  
7. Phase  
8. Signal source  
9. Color adjustment  
10. Volume  
11. Sharpness  
DVI Model  
11  
 
12. OSD position/transparency  
13. Recall  
14. Languages  
15. Exit  
16. Selected function name  
17. Resolution  
18. H-frequency  
19. V-frequency  
20. Progressive bar of adjustment  
21. Percentage of adjustment  
22. Planar LOGO  
3.3.5 Meaning of the Menu in DVI Mode  
1. Brightness  
2. Contrast  
3. Sharpness  
4. Volume  
5. OSD menu display time  
6. Transparency  
7. OSD position  
8. Signal source  
9. 9300k  
10. 7800k  
11. 6500k  
12. User  
13. Recall  
14. Language  
15. Exit  
16. Selected function name  
17. Resolution  
18. H-frequency  
19. V-frequency  
20. Progressive bar of adjustment  
21. Percentage of adjustment  
22. Planar LOGO  
12  
 
3.3.6 Function Table  
Display contents  
Function  
Automatically adjust to obtain the best  
setting  
AUTO ADJUSTMENT  
BRIGHTNESS  
Adjust the brightness  
CONTRAST  
H-POSITION  
V-POSITION  
CLOCK  
Adjust the contrast  
Move the screen toward left or right  
Move the screen upward or downward  
Adjust the frequency of pixel  
Adjust the phase of pixel clock  
Adjust the sharpness of the picture  
Adjust the colors of the picture  
PHASE  
SHARPNESS  
COLOR  
9300K COLOR TEMPERATURE Set 9300k color temperature  
7800K COLOR TEMPERATURE Set 7800k color temperature  
6500K COLOR TEMPERATURE Set 6500k color temperature  
USER MODE  
Set user mode  
AUTO COLOR BALANCE  
Auto color balance  
VOLUME  
Adjust the volume  
OSD DISPLAY TIME  
OSD ADJUSTMENT  
Adjust the OSD display time  
Adjust the parameter of OSD  
OSD H-POSITION  
OSD V-POSITION  
OSD TRANSPARENCY  
Signal source  
Move the menu toward left or right  
Move the menu upward or downward  
OSD transparency setting  
Exchange signal mode between VGA and  
DVI  
RECALL  
Reset factory setting  
LANGUAGE  
Language selection  
Exit the menu  
EXIT  
13  
 
3.3.7 Special Functions  
Auto Adjustment (  
)
When you choose this function, the monitor will  
enter into automatically adjustment mode. After a  
few seconds, the monitor will be in the best visual  
display mode.  
Color Adjustment (  
):  
When the function is selected, the monitor will come into the sub-menu, there are  
five functions that can be selected:  
9300k, 7800k, 6500k, USER,W-B. Selecting USER you will enter user mode and  
you can make adjustment to R/G/B obtain your satisfying color. Selecting W-B the  
monitor will adjust the white-black color reference voltage optimal color balance.  
R/G/B Adjustment (  
):  
When in “User’s mode”, the monitor will automatically enter into R/G/B adjustment  
mode, push the ENTER key ,the relative options will flash, then adjust it by  
pressing “+/-“ key. push ENTER again to exit.  
Language (  
).  
There are six languages to select:  
PYC.: Russian  
ENG.: English  
FRE.: French  
DEU.: German  
ITA.: Italian  
ESP.: Spanish  
Position of OSD Menu (  
):  
When you select the item, you can adjust H-position and  
V-position of OSD menu and transparency.  
Sharpness Adjustment (  
):  
Adjust the sharpness of the picture on the screen.  
14  
 
3.4 Safety Mode  
When the video signal exceeds the frequency range of the monitor, the monitor  
MCU will stop horizontal and vertical scanning in order to protect the monitor the  
following image will be displayed on the screen. After a few seconds, the monitor  
will enter turn-off mode. You must restart the computer and reset the frequency  
range.  
3.5 Timing guide  
V-Frequency  
(Hz)  
H-Frequency  
(KHz)  
No. Mode Resolution  
Available Input Signal  
Analog RGB,Digital DVI  
1
60  
72  
75  
60  
72  
75  
60  
70  
75  
31.5  
37.9  
37.5  
37.9  
48.1  
46.9  
48.4  
56.5  
60  
Analog RGB  
VGA  
640 x 480  
2
Analog RGB  
3
Analog RGB,Digital DVI  
Analog RGB  
4
SVGA 800 x 600  
5
Analog RGB  
6
Analog RGB,Digital DVI  
Analog RGB  
7
1024 x 768  
XGA  
8
Analog RGB  
9
Analog RGB  
10  
11  
12  
13  
1280 x 960 60  
60  
Analog RGB  
1152 x 864 75  
60  
67.5  
64  
Analog RGB,Digital DVI  
Analog RGB  
SXGA 1280x1024  
75  
80  
15  
 
3.6 Plug & Play  
This monitor meets the standard of VESA DDC. When using video card with  
VESA DDC1/2B, it will auto-scan video frequency, output power , function and  
other data to the PC when computer is on. It will go into the proper video mode  
and frequency.  
3.7 Power Management  
This monitor complies with EPA energy star requirement and meets VESA DPMS  
standard. The following is the description of the power indicator for the power  
saving mode.  
Mode  
On  
Stand by/suspend  
Off  
Power Indicator  
Green  
Red flashing  
Off  
Power Consumption  
<45 W  
<5 W  
<2W  
3.8 Volume Adjust  
Adjust the volume by OSD menu and software of the PC. The volume can be set  
by +/- key directly.  
16  
 
4. Specifications  
Model  
PQ1910M  
Panel  
19  
Resolution  
Active area  
Pixel pitch  
Contrast  
1280 x 1024  
376 mm x 301mm  
0.294mm x 0.294mm  
700:1  
Brightness  
300 cd/m2  
Response time  
8ms  
Display colors  
16.2 M  
Viewing angle CR>10  
H-Frequency  
V-Frequency  
H:140°V:140°  
51.2~82.1 kHz  
48~77 Hz  
Plug & Play  
Yes  
Input signal  
Analog / Digital  
15 pins D-Sub /DVI  
1 Stereo input  
2 x 2 W  
Power jack  
<45 W  
Video Input connector  
Audio input connector  
Built-in speakers  
Power input connector  
Maximum power cons.  
Stand-by power cons.  
Off mode power cons.  
Power supply for adapter  
Power supply for monitor  
Power saving control  
Norms  
<5 W  
<2 W  
100 V-240 VAC 50/60Hz  
12 VDC 4 A  
Yes  
UL, CE, CB, FCC Class B Part 15  
86kpa~104kpa  
-20°C~+55°C5%-95%  
5°C~40°C  
Atmosphere pressure  
Storage temperature and humidity  
Operating temperature  
Humidity  
10%~85%  
Unpacking dimension  
Packing dimension  
Net weight  
430 x 150 x 420 mm  
485mm x 165mm x 460mm  
6.5 kg  
Gross weight  
7.6 kg  
Note: These specifications are subject to change without notice.  
17  
 
5. Simple Troubleshooting  
Symptom  
Solution  
Check if the power cord, the monitor and the power plug  
are well connected. Check also if the monitor is off.  
No picture / no LED  
Check if the PC video card and signal cable are well  
connected and check if signal cable is properly connected  
with monitor.  
No picture  
flashing  
/
Red LED  
Picture is blurry, to big or In OSD menu select “  
” to make the monitor adjust  
small  
automatically.  
Picture is too dark  
Enter OSD menu and adjust contrast and brightness.  
Keep 5 cm away from other goods for ventilation. Don’t put  
anything on the monitor.  
Overheating  
Check the PC setting, select the proper resolution and  
adjust refresh frequency.  
Picture distortion and flicker  
Short of color  
Check if the signal cable pins are twisted or broken.  
There may be noise signals turning off the monitor.  
This is caused by electrical release and is normal.  
Noise Signals at Turning off  
18  
 
19  
 
Planar Systems, Inc.  
Customer Service  
Tel1-866-PLANAR-1 (1-866-752-6271)  
HoursM-F, 8am-8pm Eastern Time (5am-5pm Pacific Time)  
© 2006 Planar Systems, Inc. Planar is a registered trademark of Planar Systems, Inc.  
Other brands and names are the property of their respective owners.  
Technical information in this document is subject to change without notice.  
E030057208  
20  
 

Peavey Musical Instrument Amplifier Classic 100 User Manual
Pelco Satellite Radio FR85011 User Manual
Pella Window 80WW0101 User Manual
Philips Electric Shaver 4853XL User Manual
Philips MP3 Player 7101 User Manual
Philips Portable CD Player EXP2540 02 User Manual
Planet Technology Security Camera ICA 106 User Manual
Polycom Cell Phone 300 and 310 User Manual
Porter Cable Trimmer 6603 User Manual
Poulan Trimmer 545164315 User Manual