Polar GPS Receiver RS800CX G3 User Manual

1. Contents of the set  
2. How to use the RS800CX receiver  
Polar Equine  
A. A RS800CX receiver: receives displays  
and records all the data measured by the  
T56H transmitter and the G3 sensor.  
The RS800CX receiver has 5 navigation buttons and an infrared window to communicate  
with the PC via the IRDA adapter.  
Use UP and DOWN to scroll through  
the different menus and adjust values (a  
bit like + and - buttons).  
RS800CX G3  
B. A G3 GPS sensor with its battery:  
measures speed and distance in real time.  
- Quick start guide -  
C.  
A
T56H transmitter  
:
measures the  
Use OK to enter a menu, to validate a  
value and to start the stopwatch.  
horse’s heart rate in real time.  
D. A ProTrainer 5 Equine edition software:  
displays a training log, graphs, tables and  
reports on your PC to further analyse the  
data recorded during training.  
Use STOP to exit a menu, to return to  
the previous display (when you made a  
mistake while adjusting a value) and to  
stop the stopwatch.  
E. (In option, an IRDA USB adapter: uses  
infrared connexion to transfer the re-  
corded data from receiver to PC.)  
Press LIGHT once and the backlight is  
activated for 5 seconds when you press  
any other button. You can also lock the  
buttons by pressing and holding the  
LIGHT button for 2 seconds.  
The Polar RS800CX G3 Equine is the most complete training system for  
horses available. It is an evolution of the "human" RS800CX training system  
and requires a good understanding of the user manual to use all its capaci-  
ties fully. If you just bought this training system and want to try it immedi-  
ately, the following quick start guide is what you need!  
3. Starting the RS800CX  
By default, the RS800CX receiver is  
switched off to save the battery.  
Press UP or DOWN to select english  
as the language to be used.  
The following settings must be done,  
even though they don’t concern the  
horse.  
Use the UP and DOWN buttons to cus-  
tomize the following basic settings.  
Press OK to validate your settings.  
If your settings are good, select Yes.  
Once the settings are done, the RS800CX  
returns automatically to the time display.  
Time display (24h/12h)  
Time  
Date (day/month/year or  
month/day/year)  
Units (kg/cm/km or lb/ft/mi)  
Weight (of the rider)  
Height (of the rider)  
Birthday (day/month/year or  
month/day/year) of the rider  
Sex (of the rider)  
It is now ready for use!  
If you got wrong somewhere, press  
STOP to return to the previous set-  
ting.  
Press OK to validate.  
If you don’t do these basic settings,  
the RS800CX will remind you set them  
before every exercise.  
Press OK to validate.  
Press OK twice to activate it.  
4. Starting the G3  
The G3 sensor uses GPS (Global Positioning System) technology to measure speed  
and distance in real time. In ideal conditions of use, its precision can reach one meter.  
The buckle located in the back of the G3  
allows you either to wear the G3 on your  
arm using the strap provided or to fix it  
on a belt or loop.  
Open the G3 buckle and pass the strap  
through the loop (Velcro on the inside).  
To ensure good detection of the GPS sig-  
nals, the G3 shouldn’t be covered and  
should be placed with the Polar logo in an  
upright position. We also recommend wear-  
ing it on the same arm as the RS800 re-  
ceiver.  
Press the button 2 seconds to start (or stop)  
the G3. A green light indicating battery status  
(B) flashes for a few seconds. Following this,  
a red light indicating detection status (A) ap-  
pears and shows that the G3 is searching for  
GPS signals.  
The battery of the G3 has an average of 10h of use. The G3 is waterproof and its solid  
design makes it resistant to most shocks and scratches.  
Pull in enough strap so your arm can fit  
through it.  
Don’t move. Once the GPS signals have  
been found (after 1 minute in average), this  
light (A) becomes green.  
Note: The light indicating battery status (B)  
becomes red when the battery is flat .  
Use a coin to unscrew and open the metal battery cover. Place the LR6 battery as indi-  
cated and screw the metal cover back into place.  
Your G3 is now ready for use!  
To ensure a good detection of the GPS  
signals, the G3 should not be covered or  
worn under clothes.  
Then adjust the size of the strap so the G3  
can’t move once placed on your arm.  
 

Pelco TV Mount HSWM12 User Manual
Philips Car Video System 150MT2 User Manual
Philips Hair Clippers HQC281 User Manual
Philips Surge Protector SPP2306WC User Manual
Pioneer Car Stereo System CDX P1270 User Manual
Pioneer Speaker System S RS3TB User Manual
Polaroid DVD Player PDV 0700K User Manual
Poulan Snow Blower 422085 User Manual
Precor Fitness Equipment Ab X100 User Manual
PYLE Audio CD Player PLCDCS90 User Manual